Technical description

Floor profile made entirely of aluminium, foreseen for installation on unfinished floor surfaces. May be used for expansion slits in floors with any type of surface finish.
An advantage of the profile is the option of installing it outside of the expansion slit, which allows using it in spots where the joints are not straight and varying width. A further advantage is the option of replacing the visible profile components without needing to remove it from the floor. The profile is characterised by high ability to compensate building movements. The use of rubber inlays and an additional insulating inlay increases protection against water and humidity intrusion into the expansion joint. The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing..
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.
Adhere to notices and remarks concerning installation.

Installation diagrams

HIDROPLASTO 418/ALR-050

HIDROPLASTO  E 418/ALR-050

HIDROPLASTO 418/ALR-100

Technical description

Profile made entirely of aluminium, foreseen for installation in expansion slits with any surface finishes. It is characterised by a smooth surface finish (ALG) or a ribbed finish (ALR), depending on the relevant needs, as well as an aesthetically pleasing look. The special profile structure allows it to transfer cave-in forces. Upon request, it is possible to use a synthetic material washer to protect the expansion slit against intrusions of water and humidity.
The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc. It is particularly recommended for use in structures such as shopping centres, office buildings, schools, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.Profile available in flat and corner form.
Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			423/ALR-030	423/ALR-050	423/ALR-070	423/ALR-090	423/ALR-100
Corner profiles			E 423/ALR-030	E 423/ALR-050	E 423/ALR-070	E 423/ALR-090	E 423/ALR-100
Fb [mm]		Nominal expansion slit width	30	50	70	90	100
	B [mm]	Total expansion profile width	150	170	190	210	230
	S [mm]	Visible profile width after installation	55	75	95	115	135
	H [mm]	Installed height	15, 20, 25, 35, 43, 48, 58	20, 25, 35, 43, 48, 58, 63, 68, 88, 108, 138
	BE[mm]	Total expansion profile width	115	125	145	165	185
	SE[mm]	Visible profile width after installation	60	80	100	120	140
	HE[mm]	Installed height	64, 69, 74, 84, 92, 97, 107	69, 74, 84, 92, 97, 107, 112, 117, 137, 157, 187
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)	40(±20)	60(±30)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 423/ALR-050

HIDROPLASTO E 423/ALR-050

HIDROPLASTO 423/ALR-070

Technical description

Overlay floor profile made entirely of aluminium, foreseen for installation at a later execution stage, on finished surfaces. It is characterised by a smooth surface finish (NALG) or a ribbed finish (NALR), depending on the relevant needs, as well as an aesthetically pleasing look.
The special profile structure allows it to transfer cave-in forces.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for use in any kinds of public buildings, such as office buildings, banks, schools, hotels, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			423/NALR-055	423/NALR-055	423/NALR-095	423/NALR-110	423/NALR-135
Corner profiles			E 423/NALR-055	E 423/NALR-075	E 423/NALR-095	E 423/NALR-110	E 423/NALR-135
Fb [mm]		Nominal expansion slit width	55	75	95	110	135
	B [mm]	Total expansion profile width	175	195	215	230	255
	S [mm]	Visible profile width after installation	175	195	215	230	255
	H [mm]	Installed height	43
	BE[mm]	Total expansion profile width	153	173	193	208	233
	SE[mm]	Visible profile width after installation	153	173	193	208	233
	HE[mm]	Installed height	100
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)	40(±20)	60(±30)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 423/NALR-055

HIDROPLASTO E 423/NALR-055

HIDROPLASTO 423/NALR-075

Technical description

Overlay floor profile made entirely of aluminium, foreseen for installation at a later execution stage, on finished surfaces.It is characterised by a ribbed surface made of high-quality aluminium, as well as an aesthetically pleasing design.
An additional synthetic material washer is used to protect the expansion slit against intrusions of water and humidity. The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for public sites such as banks, airport halls, railway stations.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			424/NALR-035	424/NALR-050
Corner profiles			E 424/NALR-035	E 424/NALR-050
Fb [mm]		Nominal expansion slit width	35	50
	B [mm]	Total expansion profile width	155	170
	S [mm]	Visible profile width after installation	155	170
	H [mm]	Installed height	30	30
	BE [mm]	Total expansion profile width	98	113
	SE [mm]	Visible profile width after installation	98	113
	HE [mm]	Installed height	90	90
W ± [mm]		Expansion slit movement compensation	12(±6)	16(±8)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 424/NALR-035

HIDROPLASTO E 424/NALR-035

HIDROPLASTO 424/NALR-050

Technical description

Floor profile made of aluminium and a cell rubber inlay. Foreseen for installation in expansion slits with any kind of surface finish. It is characterised by a smooth surface and an aesthetically pleasing design. The special profile structure allows it to transfer high loads.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			425/AL
Corner profiles			E 425/AL
Fb [mm]		Nominal expansion slit width	35
	B [mm]	Total expansion profile width	175
	S [mm]	Visible profile width after installation	43
	H [mm]	Installed height	60
	BE[mm]	Total expansion profile width	114
	SE[mm]	Visible profile width after installation	45
	HE[mm]	Installed height	119
W ± [mm]		Expansion slit movement compensation	16(±8)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755, synthetic material – cellular rubber
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO425/AL-035

HIDROPLASTO E 425/AL-035

HIDROPLASTO 425/AL-035

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits in floors with any type of surface finish. It is characterised by a slip-protecting surface and an aesthetically pleasing look.It is characterised by a smooth surface finish (ALG) or a ribbed finish (ALR), depending on the relevant needs, as well as an aesthetically pleasing look. The special profile structure allows it to transfer cave-in forces. Upon request, it is possible to use a synthetic material washer to protect the expansion slit against intrusions of water and humidity.
The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.
Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			426/ALR-040	426/ALR-065	426/ALR-100	426/ALR-050	426/ALR-080	426/ALR-100
Corner profiles			E 426/ALR-040	E 426/ALR-065	E 426/ALR-100	E 426/ALR-050	E 426/ALR-080	E 426/ALR-100
Fb [mm]		Nominal expansion slit width	40	65	100	50	80	100
	B [mm]	Total expansion profile width	160	190	230	155/175*	180/200*	225/245*
	S [mm]	Visible profile width after installation	60	90	130	70	95	135
	H [mm]	Installed height	20			43/ 48*/ 58/ 63*/ 68/ 88/ 108
	BE[mm]	Total expansion profile width	120	150	210	115/125	140/150	183/193
	SE[mm]	Visible profile width after installation	63	93	133	73	98	138
	HE[mm]	Installed height	54			77, 82, 92, 97, 102, 122, 142
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 426/ALR-050

HIDROPLASTO E 426/ALR-050

HIDROPLASTO 426/ALR-080

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits in floors with any type of surface finish. It is characterised by a slip-protecting surface and an aesthetically pleasing look. The special profile structure allows it to transfer cave-in forces. Upon request, it is possible to use a synthetic material washer to protect the expansion slit against intrusions of water and humidity.
The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing.The non-skid profile surface guarantees safety of use in the area of the joint.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for use in public buildings, i. e. schools, pre-schools, railway stations, shopping centres, meaning – everywhere, where foot traffic is increased and where safety is required.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			426/ALR-RS-040	426/ALR-RS-065	426/ALR-RS-100	426/ALR-RS-050	426/ALR-RS- 080	426/ALR-RS- 100
Corner profiles			E 426/ALR- RS-040	E 426/ALR- RS-065	E 426/ALR- RS-100	E 426/ALR- RS-050	E 426/ALR- RS-080	E 426/ALR- RS-100
Fb [mm]		Nominal expansion slit width	40	65	100	50	80	100
	B [mm]	Total expansion profile width	160	190	230	155/175*	180/200*	225/245*
	S [mm]	Visible profile width after installation	60	90	130	70	95	135
	H [mm]	Installed height	20			43/ 48*/ 58/ 63*/ 68/ 88/ 108
	BE[mm]	Total expansion profile width	120	150	210	115/125	140/150	183/193
	SE[mm]	Visible profile width after installation	63	93	133	73	98	138
	HE[mm]	Installed height	54			77, 82, 92, 97, 102, 122, 142
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 426/ALR-RS-050

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits with any surface finishes. It is characterised by a smooth surface finish (ALG) or a ribbed finish (ALR), depending on the relevant needs, as well as an aesthetically pleasing look. The special profile structure allows it to transfer cave-in forces. The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for use in any kinds of public buildings, such as office buildings, banks, schools, hotels, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			426/ALRV-035	426/ALRV-050	426/ALRV-080	426/ALRV-100
Corner profiles			E426/ALRV-035	E426/ALRV-050	E426/ALRV-080	E426/ALRV-100
Fb [mm]		Nominal expansion slit width	35	50	80	100
	B [mm]	Total expansion profile width	155	155/175*	180/200*	225/245*
	S [mm]	Visible profile width after installation	70	70	95	135
	H [mm]	Installed height	43	43/ 48*/ 58/ 63*/ 68/ 88/ 108
	BE [mm]	Total expansion profile width	115	115/125	140/150	183/193
	SE [mm]	Visible profile width after installation	73	73	98	138
	HE [mm]	Installed height	77	77, 82, 92, 97, 102, 122, 142
W ± [mm]		Expansion slit movement compensation	10(±5)	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 426/ALRV-080

HIDROPLASTO E 426/ALRV-080

HIDROPLASTO 426/ALRV-080

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits in floors with any type of surface finish. It is characterised by a slip-protecting surface and an aesthetically pleasing look. The special profile structure allows it to transfer cave-in forces.
The entire visible profile surface is made of high-quality ribbed aluminium, making the profile suitable for rooms with high-quality finishing. The non-skid profile surface guarantees safety of use in the area of the joint.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for use in public buildings, i. e. schools, pre-schools, railway stations, shopping centres, meaning – everywhere, where foot traffic is increased and where safety is required.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			426/ALRV-RS-035	426/ALRV-RS-050	426/ALRV-RS-080	426/ALRV-RS-100
Corner profiles			E426/ALRV-RS-035	E426/ALRV- RS-050	E426/ALRV-RS-080	E426/ALRV-RS-100
Fb [mm]		Nominal expansion slit width	35	50	80	100
	B [mm]	Total expansion profile width	155	155/175*	180/200*	225/245*
	S [mm]	Visible profile width after installation	70	70	95	135
	H [mm]	Installed height	43	43/ 48*/ 58/ 63*/ 68/ 88/ 108
	BE[mm]	Total expansion profile width	115	115/125	140/150	183/193
	SE[mm]	Visible profile width after installation	73	73	98	138
	HE[mm]	Installed height	77	77, 82, 92, 97, 102, 122, 142
W ± [mm]		Expansion slit movement compensation	10(±5)	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 426/ALRV-RS-050

HIDROPLASTO E 426/ALRV-RS-050

HIDROPLASTO 426/ALRV-RS-080

Technical description

Overlay floor profile made entirely of aluminium, foreseen for installation at a later execution stage, on finished surfaces. It is characterised by a smooth surface finish (NALG) or a ribbed finish (NALR), depending on the relevant needs, as well as an aesthetically pleasing look. Foreseen for installation in expansion slits with any kind of surface finishes.
The special profile structure allows it to transfer cave-in forces.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for use in any kinds of public buildings, such as office buildings, banks, schools, hotels, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			426/NALR-070	426/NALR-100
Corner profiles			E426/NALR-070	E426/NALR-100
Fb [mm]		Nominal expansion slit width	70	100
	B [mm]	Total expansion profile width	175	200
	S [mm]	Visible profile width after installation	175	200
	H [mm]	Installed height	43	43
	BE [mm]	Total expansion profile width	150	175
	SE [mm]	Visible profile width after installation	150	175
	HE [mm]	Installed height	85	85
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO  426/NALR-070

HIDROPLASTO  E 426/NALR-070

HIDROPLASTO  426/NALR-100

Technical description

Overlay floor profile made entirely of aluminium, foreseen for installation at a later execution stage, on finished surfaces. It is characterised by a slip-protecting surface and an aesthetically pleasing look.The special profile structure allows it to transfer cave-in forces.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
The non-skid profile surface guarantees safety of use in the area of the joint.
Particularly recommended for use in public buildings, i. e. schools, pre-schools, railway stations, shopping centres, meaning – everywhere, where foot traffic is increased and where safety is required.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Profile available in flat and corner form.

Technical details
Flat bar profiles			426/NALR-RS-070	426/NALR-RS-100
Corner profiles			E426/NALR-RS-070	E426/NALR-RS-100
Fb [mm]		Nominal expansion slit width	70	100
	B [mm]	Total expansion profile width	175	200
	S [mm]	Visible profile width after installation	175	200
	H [mm]	Installed height	43	43
	BE [mm]	Total expansion profile width	150	175
	SE [mm]	Visible profile width after installation	150	175
	HE [mm]	Installed height	85	85
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 426/NALR-RS-070

HIDROPLASTO  E 426/NALR-RS-070

HIDROPLASTO  426/NALR-RS-100

Technical description

Profile made entirely of aluminium, foreseen for installation in expansion slits with any surface finishes. It is characterised by a smooth surface finish (ALG) or a ribbed finish (ALR), depending on the relevant needs, as well as an aesthetically pleasing look.The special profile structure allows it to transfer high loads and cave-in forces.
The entire visible surface of the profile is made of high-quality ribbed aluminium, making the profile become a perfect fusion of aesthetics and usability, as a result of which it is particularly recommended for warehouse halls and manufacture halls, wholesalers as well as public buildings.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			427/ALR-040	427/ALR-065	427/ALR-100
Corner profiles			E427/ALR-040	E427/ALR-065	E427/ALR-100
Fb [mm]		Nominal expansion slit width	40	65	100
	B [mm]	Nominal expansion slit width	197	228	265
	S [mm]	Visible profile width after installation	97	128	165
	H [mm]	Installed height	18,5/ 32/ 45,5
	BE [mm]	Total expansion profile width	175	206	244
	SE [mm]	Visible profile width after installation	100	131	168
	HE [mm]	Installed height	85/ 98,5/ 112
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO  427/ALR-040

HIDROPLASTO  E 427/ALR-040

HIDROPLASTO  427/ALR-065

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits in floors with any type of surface finish. It is characterised by a slip-protecting surface and an aesthetically pleasing look.
The special profile structure allows it to transfer strong forces and cave-in forces.
The non-skid profile surface guarantees safety of use in the area of the joint.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for warehouse halls and manufacture halls, wholesalers as well as public buildings.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			427/ALR-RS-040	427/ALR-RS-065	427/ALR-RS-100
Corner profiles			E427/ALR-RS-040	E427/ALR-RS-065	E427/ALR-RS-100
Fb [mm]		Nominal expansion slit width	40	65	100
	B [mm]	Total expansion profile width	197	228	265
	S [mm]	Visible profile width after installation	97	128	165
	H [mm]	Installed height	18,5/ 32/ 45,5
	BE [mm]	Total expansion profile width	175	206	244
	SE [mm]	Visible profile width after installation	100	131	168
	HE [mm]	Installed height	85/ 98,5/ 112
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO  427/ALR-RS-040

HIDROPLASTO  E 427/ALR-RS-040

HIDROPLASTO  427/ALR-RS-065

Technical description

Profile made entirely of aluminium, foreseen for installation in expansion slits with any surface finishes. It is characterised by a smooth surface finish (ALG) or a ribbed finish (ALR), depending on the relevant needs, as well as an aesthetically pleasing look. The special profile structure allows it to transfer high loads and cave-in forces.
The entire visible surface of the profile is made of high-quality ribbed aluminium, making the profile become a perfect fusion of aesthetics and usability, as a result of which it is particularly recommended for warehouse halls and manufacture halls, wholesalers as well as public buildings.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			427/ALRV-040	427/ALRV-065	427/ALRV-100
Corner profiles			E427/ALRV-040	E427/ALRV-065	E427/ALRV-100
Fb [mm]		Nominal expansion slit width	40	65	100
	B [mm]	Total expansion profile width	197	228	265
	S [mm]	Visible profile width after installation	97	128	165
	H [mm]	Installed height	32/ 45,5
	BE [mm]	Total expansion profile width	175	206	244
	SE [mm]	Visible profile width after installation	100	131	168
	HE [mm]	Installed height	85/ 98,5
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 427/ALRV-040

HIDROPLASTO E 427/ALRV-040

HIDROPLASTO 427/ALRV-065

Technical description

Floor profile made entirely of aluminium, foreseen for installation in expansion slits in floors with any type of surface finish. It is characterised by a slip-protecting surface and an aesthetically pleasing look.
The special profile structure allows it to transfer high loads and cave-in forces.
The non-skid profile surface guarantees safety of use in the area of the joint.
The profile finds use for various kinds of floor finishes, i. e. screed, natural stone, stone imitation, etc.
Particularly recommended for warehouse halls and manufacture halls, wholesalers as well as public buildings.
The profile conforms to fire resistance requirements for class E according to standard PN-EN 13501-1, according to which the products are able to stand up to the effects of a small flame without significant flame spreading – for a short time.
Profile available in flat and corner form.

Adhere to notices and remarks concerning installation.

Technical details
Flat bar profiles			427/ALRV-RS-040	427/ALRV-RS-065	427/ALRV-RS-100
Corner profiles			E427/ALRV-RS-040	E427/ALRV-RS-065	E427/ALRV-RS-100
Fb [mm]		Nominal expansion slit width	40	65	100
	B [mm]	Total expansion profile width	197	228	265
	S [mm]	Visible profile width after installation	97	128	165
	H [mm]	Installed height	32/ 45,5
	BE [mm]	Total expansion profile width	175	206	244
	SE [mm]	Visible profile width after installation	100	131	168
	HE [mm]	Installed height	85/ 98,5
W ± [mm]		Expansion slit movement compensation	10(±5)	20(±10)	30(±15)
Colour			natural
Material			aluminium – properties according to standard PN-EN 755
Load [kN]**
Standard length [m]			4

Installation diagrams

HIDROPLASTO 427/ALRV-RS-040

HIDROPLASTO  E 427/ALRV-RS-040

HIDROPLASTO  427/ALRV-RS-065

Product description

An expansion joint (dilation joint, from Latin dilatare: to expand, to extend) is a purposefully created slit in a building or structure, the task of which is to allow individual component of the structure to work independently of the rest. Separate components transfer loads, deformations and movements by themselves. Expansion joints are executed to protect the structure from:

– concrete contraction and temperature differences that can cause cracks or fractures of a reinforced steel structure,

– unequal setting,

– concrete creep.

• structural joints – they separate a part of the building forming one complete whole with respect to statics, manufacture technology and foreseen site use, or stem from its grand proportions. They are used if a foundation method is changed, a building’s structural arrangement is changed or load differences are great. They separate all structural components across one section, from the foundation to the roof,
• thermal expansion joints – they work to contract or expand and protect the building against cracks arisen as a result of temperature changes. They act to eliminate the influence of large stresses from thermal deformations of individual building components,
• anti-vibration expansion joints – in most cases associated with industrial structures, where they are supposed to protect the site or its constituent components against the influence of vibrations (dynamic and/or acoustic influences) from foundations and the framework profiles on which machines are placed. Similar properties and a similar requirement of use for a structure may be imposed by virtue of a building’s location in the area of influence of seismic waves caused by earthquakes or mining damage,
• expansion joints allowing unequal structure setting – the phenomenon of setting stems from mechanical properties of soil, and in particular, from its compression ability, or the ability to reduce its volume under the influence of load. If the soil conditions change under the foundations, within the outline of the building’s silhouette, then its subdivision into individually working parts is substantiated from the economic point of view. One needs to remember that expansion joints should be designed in buildings along their entire height, from the foundation to the roof.

A national annex to Polish standard PN-EN 1992-1-1 indicates the maximum distances between expansion joints:

Possible directions of movement of building parts connected by expansion joints.

Structures and their details are always subjected to influences by diverse forces that are the result of setting, temperature and humidity variations, static and dynamic loads. These forces cause tensions within components, which can cause the emergence of irreversible changes in the parts or cause the material to crack, or in the extreme cases, to fracture.
In order to reduce the possibility of permanent damage emerging or of damage spreading to other parts of the structure, individual building components are allowed to work independently with respect to their statics. This requirement is fulfilled by the designed structure joints – expansion joints.

Mutual movements and the width of the expansion joint are determined in the design phase. Of significant importance during the design phase is the designing entity that decides on the choice of appropriate expansion profile system. The contractor in turn should adhere to recommendations and instructions of the expansion joint profile system manufacturer
The choice of appropriate profiles for installation of the expansion joints is thus decisive for their proper operation.
Should the issue not be treated seriously enough, damage such as surface cracks, fractures on corners, structure humidity, flaws and profile structure damage will emerge.
In case of expansion joints in floors of industrial and warehouse structures, one should consider, beside the width of the slits, also the thickness of the floor surface and the movement values to be expected, loads from wheels of transport vehicles and their tyre types.
Information on tyre types is very important, because one assumes the use of vehicles with small wheels that have a small width, made i. e. of hard polyamide or vulkollan.
Point loads that are then transferred to the expansion joint protection component (profile) are very high, and even if the slits are comparably narrow, appropriately massive expansion profile structures need to be used.
How the pressure forces and pull forces act on the structure, is presented in the image below.

For floor profiles, static tests were conducted according to load data for forklift trucks per norm PN-EN 1991-1-1 and DIN 1072 – loads from vehicle traffic.

In case of proper profile choice, the following decisive criteria should be taken into account:
a) allowable horizontal shift ±
b) allowable vertical shift – surface setting (i. e. cave-in area, earthquake area or joints of new buildings with existing structures),
c) expansion joint width,
d) height of profile installation into structure,
e) visible profile part,
f) other materials, with which the profile will come into contact (i. e. screed, asphalt),
g) normal loads (standards per PN-EN and DIN 1072),
h) place of use, i. e. structures with high hygiene and sanitary requirements (hospitals, schools, etc.),
i) aggressive media (chemical industry, milk manufacture plants, etc.),
j) providing the interior with a particular aesthetic design,
k) option of installation on the finished floor surfaces at a later construction phase or in unfinished surfaces.

The load table, according to which an initial choice of expansion profile may be made, is found below.

Deflex floor profile load table
Load type	According to norm	Vehicle type	Maximum static vertical load from vehicle axle [kN]	Area of tyre adherence to surface [cm]	Separation between components anchoring the profile to the grounda [cm]	Distance from last anchor to profile end [cm]
	PN-EN 1991-1-1 DIN 1055	Forklift truck	26	20/20	30	15
	PN-EN 1991-1-1 DIN 1055		40	20/20	30	15
	PN-EN 1991-1-1 DIN 1055		63	20/20	30	15
	PN-EN 1991-1-1 DIN 1055		90	20/20	30	15
	PN-EN 1991-1-1 DIN 1055		140	20/20	30	15
	PN-EN 1991-1-1 DIN 1055		170	20/20	30	15
	DIN 1072	Goods truck	40	20/30	30	15
	DIN 1072		30	20/26	30	15
	DIN 1072		20	20/20	30	15
	DIN 1072		50	20/40	30	15
	DIN 1072		100	20/60	30	15
	particular situation	Pallet lifter	10	2/3	30	15
	PN-EN 1991-1-1	Light vehicle ≤ 30 kN	10	20/20	30	15

Considering structure reliability, usability as well as aesthetics and functionality of a site, one should make all effort to provide appropriate protection of expansion joints. Experience shows that increased expense borne in this respect and high professional quality of the contractor limit to a great extent expenditures for refurbishment and mitigate difficulties during site use.
This catalogue should be helpful material for the purpose of design of expansion slit execution and for the choice of appropriate profiles.
In case of any doubts, please contact our technical advisors. We are convinced that we able to provide optimum solutions even for the most uncommon situations.
In case of queries concerning the choice of expansion profile, please indicate:

• expansion slit width,
• expansion slit movement compensation,
• structure profile installation height,
• load amount,
• point of installation.

In the following table are presented the most important properties of Deflex expansion profiles, facilitating the initial choice of the proper solution.

Expansion profile types		Load type	Expansion slit width [mm]	Material		Movement direction
				Aluminium	Others	Levels	Vertical	Horizontal
DEFLEX 418			50-100	.		.		.
DEFLEX 423/ALR			30-100	.		.	.	.
DEFLEX 423/NALR			55-135	.		.	.	.
DEFLEX 424/NALR			35-100	.		.		.
DEFLEX 425/AL			35	.	rubber	.		.
DEFLEX 426/ALR			40-100	.		.	.	.
DEFLEX 426/ALR-RS			40-100	.		.	.	.
DEFLEX 426/ALRV			35-100	.		.	.	.
DEFLEX 426/ALRV-RS			35-100	.		.	.	.
DEFLEX 426/NALR			70-100	.		.	.	.
DEFLEX 426/NALR-RS			70-100	.		.	.	.
DEFLEX 427/ALR			40-100	.		.	.	.
DEFLEX 427/ALR-RS			40-100	.		.	.	.
DEFLEX 427/ALRV			40-100	.		.	.	.